Honeywell Wireless Alarm Sensors

CCTV System
Access Control
Intruder Alarm
Wired Alarm System
Wireless Alarm System
Control Panels
Wired Alarm Sensors
Wireless Alarm Sensors
Zone Expanders 
Speech Dialers
GSM Data Dialer
Alarm Monitoring
Guard Tour
Public Address
Door Entry

      Wireless Door/ Window Contact

      This wireless sensors is installed on doors and windows. If it is

      installed on doors it can be programmed as Entry/Exit zone. If it is

      installed on windows then it can be programmed as Perimeter zone.

      Wireless Motion Detector

      This wireless sensor is installed on the path ways and other areas

      If it detects any motion then it will trigger alarm if the system is in

      armed state. It is mainly programmed as Follower zone.

      Wireless Glass Break Detector

      This wireless sensors is installed near glass doors or windows,

      It triggers alarm if any glass is broken while the system is in armed

      state. This device can be programmed in Perimeter zone.

      Wireless Remote Button

      This wireless remote control is used for arming and disarming the

      system. Four buttons are available each button can be programmed

      for Arm Away, Arm Stay, Disarm and Panic modes.

      Wireless Receiver

      This devices connects all the wireless sensors installed with the main

      Control Panel.
Wireless Alarm Sensors
          Honeywell wireless alarm sensors are used in Intruder alarm systems
for Villas and offices where cabling has to be minimal to preserve the asthetics
of the property.

             Various alarm sensors
are used like door and window sensors, motion PIR, Glass break detector and
remote buttons.

              Wireless door and
window sensors are installed along a magnet  on doors and windows. These
sensors work on magnetic technology. If a door or window is opened then the
sensors sends an open signal to the main Control panel. A single battery is used
which can last up to a year and also depends on the usage. If there is a
mosquito net on the window then the sensor or magnet will be installed on the
net. This provided both security as well as the window can be kept open without
allowing the mosquitoes to enter the house. If any intruder opens the mosquito
net then the alarm will be triggered if the system is in armed mode.

            Door senors are programmed as
entry / exit zones if they are installed on the main doors. This will give an
entry / exit delay for the duration programmed. The delay can be programmed from
30 seconds to 45 seconds normally. The system will give a delay with beep sound
for the duration to disarm the system while entering or to exit.

             Wireless motion PIR used
to detect any movement in the protected site. This sensor works on the infra red
rays technology. each living thing emits certain amount of infra red rays which
is detected by the sensor. These sensors are installed in pathways to detect
motion. If there is any movement while the system is in armed state it will
trigger alarm.

            Motion detectors are
programmed as follower zone. If the main entry / exit zone is opened first then
the motion detector will not trigger alarm till the duration of the delay. If
the entry zone is not opened and the motion detector detects motion then it will
trigger immediate alarm.

            These sensors should be
avoided if there are pets at home or the protected site.

          Wireless Glass break detectors are used to detect any breaking of
glass windows or doors. These sensors are installed near glass doors or windows.
They work on sound technology. These sensors detect the frequency of breaking of
glass and trigger alarm if the system is in armed state. These sensors are
programmed as perimeter zones to trigger alarm immediately in armed state.

            Remote buttons are used to arm and
disarm the system without using the keypad. These devices are used for
convenience where with one press of a button you can arm or disarm without
having to enter the code in the keypad. There are four buttons. One for arming
in Away mode, second for arming in Stay mode, third for disarming the system and
the fourth one is a panic button where the alarm can be triggerd immediately if
you press this button.

            Wireless receiver is used to
communicate and connect all the wireless sensors with the main control panel. If
the sensors are installed at both ground floor and first floor then it is
recommended to have one receiver at each floors. These devices are installed at
the center location of the protected site and they are hardwired with the main
control panel. The power is supplied to these receivers by the control panel.
These sensors can be installed on the false ceiling or walls depending upon the
site condition.